Dodge Charger Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-20 of 58 Results
  1. Dodge Charger Parts for Sale - Trade - WTB.
    Like new LMI Frankentake CAI for 6.1L hemi. Purchased for 08 SRT8 Charger, then traded the vehicle a short time later. Has been kept in a box since. Message with any questions. Thank you.
    $100 USD
  2. Dodge Charger General Discussion
    On most cars that checked the intake temperature is usually around the outside air temperature. Even if they're not officially a cold air intake. Meanwhile the intake of my car (wich has the intake going down to the wheel stock) is in the 150° range except on the highway. Any way to lower that?
  3. Dodge Charger Parts for Sale - Trade - WTB.
    Hello, All parts are off of a 2019 Scatpack Charger with less than 1500 miles. Car is being sold so parts are next. 3. Unlocked PCM / Trinity-2 EX with OBD cable & bypass cable (OBD cable has slight wear, covered with electrical tape, functions fine) - $575 shipped OBO - The PCM must be sent...
  4. Dodge Charger Parts for Sale - Trade - WTB.
    This is the RPM Motorsports Dodge Charger 3.6L Intake Resonator Delete Kit. I bought this over the holidays and by the time it arrived I no longer had the car. So my loss is your gain, if you have any questions feel free to message me and I will try my best to answer them. This should fit any...
  5. Newbie Check In!
    Hey everybody, a couple of months ago I purchased a super clean 2006 RT with 112k miles. Since having it I've really only straight piped it as far as "building" goes, but I'm looking into upgrading my air intake. I've heard a lot of good things about LMI (preferably looking into the "LX / LC...
  6. Charger Performance Mods - Engine - 6.4L HEMI
    Hello I recently purchased a Injen intake for my 6.4 and I’m wondering if anyone else got one on their 392. I’m worried that the gains won’t be the same as other intakes or am I over my head? Another worry would be if it’ll get heat soaked fast. It’s in a position where they try to avoid it and...
  7. Charger Performance Mods - Engine - 3.6L
    I currently have an AFE Magnum dry flow filter in my airbox. Its the only performance mod I have on my 19 GT, Im wondering if upgrading to an Araid 350-317 would be worth it. I know cais dont provide as much hp as advertised but im looking for a better throttle response and sound. Any thoughts...
  8. Dodge Charger Parts for Sale - Trade - WTB.
    Trying to find a ported upper and lower intake manifold for a 3.6. If you have just a lower, or just an upper, I might still be interested
  9. Dodge Charger Parts for Sale - Trade - WTB.
    Hey guys, I'm in the process of trading up to a 392, so because of that, I'm selling some parts that I have. All are in excellent condition, some used for less thank 1K miles. UPR 6oz Brushed Silver Billet Catch Can with Z-bracket, braided hoses and matching fittings (only used a 1.5 months)...
  10. Dodge Charger Parts for Sale - Trade - WTB.
    Carbon fiber Legmaker intake: Approximately 10k miles on the intake. Sold the car so no longer need.
  11. Dodge Charger Parts for Sale - Trade - WTB.
    Hello, it seems as though no company will ship to CA (Shit State) even if the intake is CA legal. So i'm hoping you guys have something. I'm not to picky on brands but i need it to have a heat shield and have a CARB#.
  12. Dodge Charger General Discussion
    Hey all, so I have the P1004 code on my '08 Charger SXT. I bought this car used and have been trying to clear this code for the past month. I installed a new runner actuator on the right side of the intake, but the code persists. Upon further research i found that some people have had success...
  13. Dodge Charger Mechanical Problems and Questions
    The motor in my 2006 3.5L went out so I swapped it for a rebuilt 2007 3.5L. A few things were different, such as the wiring for the camshaft sensor, but I figured most of it out. My problem now is the upper intake. The intake for the 2007 has 5-pin sensors for the intake manifold actuator and...
  14. Dodge Charger Parts for Sale - Trade - WTB.
    Gently used, only on for 1k Miles before I sold the car. Comes with original box and instructions, and all parts Will fit Charger,Challenger, 300’s with 6.4L(srt or scat pack) Located in Chicago Can ship $75 with pick up, shipping would be $20 via UPS
  15. Charger Performance Mods - Engine - 6.4L HEMI Part # 77070043AC As we all know the Daytonas come with the Mopar performance intake. Now I don't doubt Mopar's ingenuity but I've always used K&N filters for my cars. I've been trying to find a K&N filter that fits...
  16. Newbie Check In!
    Where my vegas people at? 16 Charger RT Mods so far: Leather Interior Trunk debadge Interior LED swap LUX smoke rear turn signals and reverse lights LUX smoke side reflectors Tinted windows Velgen "Classic 5" Wheels Mods planned Lower it (Need help! Bags or coils?!) HID headlights Re-tint...
  17. Charger Performance Mods - Engine - 3.6L
    Nothing huge but ever bit helps right! :cool:
  18. Dodge Charger Parts for Sale - Trade - WTB.
    Used on 2006 Charger R/T. Used. Has gasket but not the mounting hardware. Located in South Jersey just east of Philadelphia.
  19. Charger Performance Mods - Engine - SXT - 3.5L
    So the 3.5 changes ever so slightly from 06 to 08. Including the intake plenum having a different valve runner setup. My questions now are can I use the 2008 plenum on the 06 engine... it's going into the 2008 car so I'm figuring I need to use the new plenum anyway because it's going to be...
  20. Charger Performance Mods - Engine - 3.6L
    I did some testing to put this myth to rest
1-20 of 58 Results